Creek | 4040 A - Integrated Amplifier + DAC
SKU:
£799.00
£799.00
per item
The all-new 4040 A integrated amplifier has been designed to reprise the essence of the original CAS4040 which was launched in 1982 to critical acclaim. While huge technological advances and modern digital features have propelled the 4040 A into the 21st century, it continues to release the same endorphins its ancestor did 40 years ago.
AVAILABLE TO ORDER - Please contact us for information on stock availability and lead time before making a purchase
Reviews
CLICK ON IMAGES FOR FULL REVIEW
   |
|
CONTROL
The 4040 A’s intuitive user interface and sophisticated menu system are easily navigated by two rotary control knobs or infra-red remote control PRE-AMPLIFIER The “feature-rich” 4040 A contains three analogue signal inputs, including two pairs of unbalanced RCA sockets and one pair of fully balanced XLR sockets, that can still be used single-ended. An electronic volume and balance control enables precise 1dB adjustments over a 70dB range. Tone controls (EQ) enable +/- 10dBs adjustment of treble and bass. PHONO Vinyl music lovers may plug-in an optional Sequel mk4 Phono pre-amp in place of Line 2 to match a wide range of Moving Magnet and high output Moving Coil cartridges found on modern turntables. HEADPHONES A high current, low distortion headphone amplifier drives a wide range of low-impedance headphones via a front panel-mounted 6.35mm (1/4”) jack socket. DIGITAL INPUTS Coaxial SPDIF, optical TOSLINK, USB class 2 and aptX Bluetooth 5.0 enables digital sources, such as music streamers, TVs, CD transports, computers, and wireless Bluetooth devices to be connected. |
DAC
PCM and DSD digital audio signals are converted to analogue with a reference quality 32-bit ES9018k2m Sabre32 DAC. POWER AMPLIFIER The 4040 A employs cutting-edge MERUS™ Infineon technology enabling it to drive even the most difficult loads to realistic listening levels with high fidelity. The power amp may be driven directly via Line 1. POWER SUPPLY The key to the integrated amplifier’s impressive performance is in its high-frequency power supply, optimised for audio electronics, enabling the latent quality of its amplifier to be realised. The performance is unaffected by mains quality or voltage stability. Unlike most conventional amplifiers, the 4040 A’s 350-Watt power supply is voltage stabilised, enabling it to double its power output into half the load impedance, regardless of the mains voltage. STANDBY Power consumption is reduced by powering-down non-essential circuitry when not required. |
Technical Specifications
|
Power output: 55 W into 8 Ohms, 110 W into 4 Ohms, both channels driven
Continuous max output current: >8A, current limited Peak current: >20A THD and Noise: <0.045% Signal to Noise Ratio: 105dBA Frequency Response: 5Hz to 50 kHz, +/-3dB / 10Hz – 20KHz +/-1dB Input sensitivity: 525mV for 55 W into 8 Ohms Gain: 32dB or x40 Crosstalk: >68dB at 1 kHz Pre-Amp Inputs: 2x RCA (unbalanced) and 1x XLR (balanced) Power-Amp Input: Power Amp Direct via a menu option Plug-in Phono options: Sequel mk4 MM Phono. 40 and 50dB gain Digital inputs: 1x co-axial, 1x optical, 1x USB 2.0 Wireless: Bluetooth aptX HD Digital to Analogue Converter: ES9018k2m Sabre DAC. |
Loudspeaker Outputs: 4mm binding posts with rear and side entry, plus a spade lug
Speaker output impedance: <0.02 Ohms 20Hz to 20 kHz. Damping Factor: >100 into <0.04 Ohms Headphone Output socket: 6.3mm stereo jack socket for 30 – 300 Ohm headphones Mains input voltage range: 100V to 240V nominal, 50Hz or 60Hz Power Consumption: <0.5W Standby, 5W Idle, 350W Full Power Auto Standby: 30, 60, 120 minutes, or disabled Finish colours: Silver or Black front panel Weight: 2.2kgs (4.85 lbs) net, 3kgs (6.6 lbs) gross (packed) Size W/H/D: 21.5 x 6 x 25.5 cm (8.46″ x 2.36″ x 10”) including feet, knobs, LS terminals and BT antenna. |
