Chord Electronics | ULTIMA Pre 2 - Reference Preamplifier
SKU:
£13,995.00
£13,995.00
per item
Featuring unrivalled connectivity and minimal colouration, the ULTIMA PRE 2 can be the hub of your Hi-Fi system without taking anything away from the incoming signal.
AVAILABLE TO ORDER | IN-STORE COLLECTION ONLY - Please contact us for information on stock availability and lead time before making a purchase
The fully modernised ULTIMA PRE 2 is built to complement stereo systems of the highest order and represents the finest Chord Electronics engineering inside and out.
Just as a preamplifier should, the ULTIMA PRE 2 adds nothing to the original waveform and instead preserves it with zero colouration. This is thanks to our latest advances in switch-mode power supply design, developed from aerospace technologies, and our ultra-low-noise proprietary solid-state circuitry which is both carefully shielded and equipped with premium system components. As a result, the ULTIMA PRE 2 is able to achieve unprecedented noise floor performance of -130dB, meaning your source will always sound like your source and nothing else.
Where connectivity is concerned, the ULTIMA PRE 2 has hi-fi systems (and more!) covered. Featuring eight inputs, four stereo pairs of XLRs for balanced connections and another four RCA for unbalanced connections, each of these can be gain-matched and individually selected. For outputs, a single stereo pair is available via XLR or RCA, to accommodate a single stereo amplifier such as the ULTIMA 5 or a pair of mono blocks such as the ULTIMA 3s. Naturally, headphone users are catered for, too, for personal and late-night listening with the addition of a high-resolution 6.35mm output on the front fascia.
Where system-triggering is important, (allowing the simultaneous start-up of connected equipment from a single button-press), the ULTIMA PRE 2 is equipped with three outputs which should be more than enough for most systems.
Just as a preamplifier should, the ULTIMA PRE 2 adds nothing to the original waveform and instead preserves it with zero colouration. This is thanks to our latest advances in switch-mode power supply design, developed from aerospace technologies, and our ultra-low-noise proprietary solid-state circuitry which is both carefully shielded and equipped with premium system components. As a result, the ULTIMA PRE 2 is able to achieve unprecedented noise floor performance of -130dB, meaning your source will always sound like your source and nothing else.
Where connectivity is concerned, the ULTIMA PRE 2 has hi-fi systems (and more!) covered. Featuring eight inputs, four stereo pairs of XLRs for balanced connections and another four RCA for unbalanced connections, each of these can be gain-matched and individually selected. For outputs, a single stereo pair is available via XLR or RCA, to accommodate a single stereo amplifier such as the ULTIMA 5 or a pair of mono blocks such as the ULTIMA 3s. Naturally, headphone users are catered for, too, for personal and late-night listening with the addition of a high-resolution 6.35mm output on the front fascia.
Where system-triggering is important, (allowing the simultaneous start-up of connected equipment from a single button-press), the ULTIMA PRE 2 is equipped with three outputs which should be more than enough for most systems.
Technical Specifications
|
Frequency Range:
2.5Hz – 200kHz +/- 3dB Total Harmonic Distortion: 0.002% 20Hz – 20kHz Intermodulation Distortion: -115dB on all inputs Signal to Noise Ratio: -120dB on all inputs Channel Separation: 20Hz @ 100dB, 1kHz @ 95dB, 10kHz @ 90dB, 20kHz @ 85dB Channel Balance: 0.01dB Input Max Voltage: 17v RMS Balanced – 8.5v RMS Unbalanced Output Max Voltage: 17v RMS Balanced – 8.5v RMS Unbalanced Output Offset: 0mV (Both Channels) Potentiometer Performance: 0dB 0.5dB, -20dB 0.2dB, -60dB 0.24dB (13seconds Full Travel) Nominal Gain: All inputs subject to six levels of switchable gain – x0.5, x1, x1.5, x2, x2.5, and x3 Input Impedance: 100 kΩ Balanced – 50 kΩ Unbalanced |
Output Impedance:
100Ω (Short Circuit Protected) Operating Voltage: 85v – 270v AC (50Hz – 60Hz) Auto Switching Power Consumption: 30w Dimensions Without Integra Legs: 420mm (w) x 355mm (d) x 133mm (h) Dimensions With Included Integra Legs: 480mm (w) x 355mm (d) x 173mm (h) Weight: 18kG FeaturesInputs & Outputs:
8 Stereo Inputs and 1 Stereo Outputs
|
